贝尔S12设备多重信令点编码用户操作手册

Ed.01StatusDate2002-6-10CategoryDoc.No.Page1/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell多重信令点编码功能用户操作手册编制:蒋东铭审核:批准:Ed.01StatusDate2002-6-10CategoryDoc.No.Page2/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell文件版本更改记录版本更改次第编写审核批准发放日期01蒋东铭2002-6-10Ed.01StatusDate2002-6-10CategoryDoc.No.Page3/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell目录1应用背景........................................................................................52.应用环境介绍................................................................................53.MNETOPER方式多信令点编码MTP数据创建流程.....................63.1添加OPC................................................................................63.2用新的OPC创对端局.............................................................83.3创链路组.................................................................................93.4创链路.....................................................................................93.5创路由...................................................................................104.MNETOPER方式多信令点编码MTP数据删除流程..................104.1删路由...................................................................................104.2删链路.................................................................................104.3删链路组...............................................................................104.4删对端局...............................................................................104.5删OPC.................................................................................115.应用环境创建流程.....................................................................145.1创路由...................................................................................145.2针对第一个OPC和相应的DPC创TUP中继群和扩中继......14Ed.01StatusDate2002-6-10CategoryDoc.No.Page4/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell5.3针对第二个OPC和相应的DPC创TUP中继群和扩中继......145.4创包含以上两个TKG的复合中继群.......................................155.5创建子路由块.........................................................................155.6创建路由块............................................................................155.7创建相应的DESTACC指向刚创建的路由块.........................155.8修改字冠对应的任务..............................................................156.功能验证.....................................................................................156.1LS_A和LS_B都Active......................................................166.2打死LS_A.............................................................................166.3LS_A和LS_B都打死............................................................16Ed.01StatusDate2002-6-10CategoryDoc.No.Page5/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell1应用背景多个电信运营商之间实现网络互通时重复使用信令点编码(MNETOPER)，要求针对相同的SSF引入多个OPC(本局信令点编码)。因此，每个SSF不再对应于一个OPC。为了确定一个OPC，必须使用SSF+OPCIND(OPC指示码1-4)。而且，当一个端局有多个SSF时，所有SSF都应该使用相同的OPCIND。网关局使用的OPC应在各运营商之间统一编码，唯一使用。其余的OPC则可以在各运营商之间任意重复使用。网关局的MTP网络管理消息必须确保OPCIND不发生混淆。2.应用环境介绍多重信令点编码（MultipleOPC）功能通常应用在网关局之间，最多可以创建四个信令点编码。互连的局之间需要同时支持。一般使用非co-located模式来实现多信令点编码，此时交换机7号信令链路与路由管理消息与使用单一信令点编码情况是一致的。S12交换机的数据结构规定多信令点编码之间只能一一对应地创建信令链路与路由，即：如果交换机a设置了信令点编码11和12，交换机b设置了信令点编码21和22，若11和21之间、12和22之间创有链路和路由，11和22之间、12和21之间就不能再创链路和路由。在这种情况下，11不能通过21向22发送STP消息或链路与路由管理消息。图2-1MultipleOPCMNETOPER方式测试环境Ed.01StatusDate2002-6-10CategoryDoc.No.Page6/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBell3.MNETOPER方式多信令点编码MTP数据创建流程MNETOPER方式是S12多信令点编码的主要实现方式，每个SSF最多可以同时添加3个MNETOPER的OPC，实现4个信令点。3.1添加OPCDINGXI_LOCAL2001-03-0210:14:20FRPW00010130/002D/0003MODIFY-N7PARM?PARAMETERMISSING:OPC=H'10001.PARAMETERMISSING:SSF=NAT,MOPCAPPL=MNETOPER.PARAMETERMISSING:NEWNAME=S1B.SEQ=0898.2001-03-02COM=0234JOBSUBMITTEDRESULTDELAYEDDINGXI_LOCAL2001-03-0210:15:35FRPW00010130/002D/0003A1112B2221Ed.01StatusDate2002-6-10CategoryDoc.No.Page7/16CopyrightShanghaiBell.Allrightsreserved.Passingonandcopyingofthisdocument,useandcommunicationofitscontentsnotpermittedwithoutwrittenauthorizationfromShanghaiBellSEQ=0898+2001-03-0200201ASKTROCHFBNQAE01HSRRIF29N7NETWORKMANAGEMENTMODIFY-N7PARMSUCCESSFULLYSTARTEDRESULTPART1-----------------------------------------------------------------------OPERATORINPUT:SSF=NATOPC=101H'0010001NEWNAME=S1BMOPCAPPL=MNETOPER-----------------------------------------------------------------------RESULT:OLDDATAEXCHNAME=DINGXI_21OPCIND=OPCSET1MOPCAPPL=NORMSSFOPC*SPLITOPC*HEXPCLENABBITSFUNCST-------------------