6.PROE_Wildfire工程特征

Pro/ENGINEERwildfire2.0工程特征建立Pro/Ewildfire2.0teachingmaterialDate:16-Dec-04Pro/E-wildfireteachingmaterialPage:2大綱1﹑孔(Hole)*2﹑殼(Shell)3﹑肋(Rib)4﹑拔模(Draft)*5﹑倒C角(Chamfer)*6﹑倒圓角(Round)*注﹕以上標題中帶*號為重點掌握Pro/E-wildfireteachingmaterialPage:31﹑關于孔特征Pro/E-wildfireteachingmaterialPage:41.1﹑使用者界面(直孔)Pro/E-wildfireteachingmaterialPage:51.1﹑使用者界面(標准孔)Pro/E-wildfireteachingmaterialPage:61.2﹑孔位置放置參照Pro/E-wildfireteachingmaterialPage:71.3﹑孔位置的放置類型Pro/E-wildfireteachingmaterialPage:82﹑關于殼特征Pro/E-wildfireteachingmaterialPage:92.1﹑使用者界面(殼)Pro/E-wildfireteachingmaterialPage:102.2﹑Shell特征注意事項Pro/E-wildfireteachingmaterialPage:112.3﹑范例﹕建立殼特征Pro/E-wildfireteachingmaterialPage:122.4﹑范例﹕建立殼特征的順序Pro/E-wildfireteachingmaterialPage:133﹑關于肋特征Pro/E-wildfireteachingmaterialPage:143.1﹑使用者界面(肋)Pro/E-wildfireteachingmaterialPage:153.2﹑草繪肋特征Pro/E-wildfireteachingmaterialPage:163.3﹑定義肋特征Pro/E-wildfireteachingmaterialPage:174﹑關于拔模Pro/E-wildfireteachingmaterialPage:184.1﹑使用者界面(拔模)Pro/E-wildfireteachingmaterialPage:194.2﹑建立拔模的一般步驟Pro/E-wildfireteachingmaterialPage:204.3﹑關于分割拔模Pro/E-wildfireteachingmaterialPage:214.4﹑范例1﹕建立基本拔模Pro/E-wildfireteachingmaterialPage:224.5﹑范例2﹕建立草繪分割拔模Pro/E-wildfireteachingmaterialPage:234.6﹑范例3﹕建立分割拔模Pro/E-wildfireteachingmaterialPage:244.7﹑范例4﹕建立可變角度拔模Pro/E-wildfireteachingmaterialPage:254.8﹑范例5﹕建立曲面分割拔模Pro/E-wildfireteachingmaterialPage:265.1﹑倒圓角類型Pro/E-wildfireteachingmaterialPage:275.2﹑倒圓角放置參照邊邊鏈曲面對邊曲面對曲面Pro/E-wildfireteachingmaterialPage:285.3﹑圓角建立方式與截面形狀Pro/E-wildfireteachingmaterialPage:295.4﹑范例1﹕建立恆定圓角Pro/E-wildfireteachingmaterialPage:305.5﹑范例2﹕建立可變圓角Pro/E-wildfireteachingmaterialPage:315.6﹑范例3﹕建立由曲線驅動的圓角Pro/E-wildfireteachingmaterialPage:325.7﹑范例4﹕建立完圓倒角Pro/E-wildfireteachingmaterialPage:336.1﹑倒C角類型與參照邊邊鏈曲面對邊曲面對曲面轉角倒角Pro/E-wildfireteachingmaterialPage:346.2﹑倒C角尺寸的布置Pro/E-wildfireteachingmaterialPage:356.3﹑范例1﹕建立倒C角Pro/E-wildfireteachingmaterialPage:366.4﹑范例2﹕建立轉角倒角Pro/E-wildfireteachingmaterialPage:376.5﹑倒C角練習﹕