您好,欢迎访问三七文档
当前位置:首页 > 行业资料 > 国内外标准规范 > 18、10kV电缆附件专用技术规范
10kV电力电缆附件专用技术规范二〇一五年七月目次1技术参数和性能要求····································································································151.1电缆附件主要电气性能参数····························································································151.2电缆附件运行参数······································································································151.3电缆附件结构参数······································································································152项目需求部分·············································································································192.1货物需求及供货范围一览表····························································································192.2必备的备品备件、专用工具和仪器仪表供货表·······································································202.3投标人应提供的有关资料······························································································212.4工程概况················································································································212.5使用条件················································································································212.6项目单位技术差异表···································································································223投标人响应部分··········································································································223.1技术偏差················································································································223.2主要原材料产地表······································································································233.3推荐的备品备件、专用工具和仪器仪表供货表·······································································231技术参数和性能要求投标人应提供符合GB和IEC最新版本的标准和本技术规范书的优质产品,应认真填写表1~表6中投标人保证值,不能空格,也不能以“响应”两字代替。不允许改动招标人要求值。如有偏差,请填写技术偏差表。1.1电缆附件主要电气性能参数电缆附件主要电气性能参数见表1。1.2电缆附件运行参数电缆附件运行参数见表2。1.3电缆附件结构参数电缆户外终端结构参数见表3,电缆户内终端结构参数见表4,电缆插拔式终端结构参数见表5,电缆接头结构参数见表6。表1电缆附件主要电气性能参数表序号项目标准参数值投标人保证值1工频电压试验≥39kV,5min,不闪络,不击穿(投标人填写)2负极性直流电压实验按照GB/T12706.435KV15min2户外终端工频电压试验(淋雨下)45kV,15min(投标人填写)3局部放电试验(室温、试验灵敏度10pC或更优,15kV下)在环境温度下,15kV下,≤5pC(投标人填写)4恒压负荷循环试验在23kV电压下60次循环不击穿(投标人填写)5局部放电试验(高温、试验灵敏度10pC或更优,15kV下)在环境温度下,15kV下,≤5pC(投标人填写)6冲击电压试验(导体温度95℃~100℃下)±95kV各10次(投标人填写)7冲击后工频电压试验23kV,15min(投标人填写)8热稳定试验按照GB/T12706.4规定数值(按电缆截面分别提供)9动稳定试验按照GB/T12706.4规定数值(按电缆截面分别提供)10户外终端盐雾试验11kV,1000h(投标人填写)11户内终端潮湿试验11kV,300h(投标人填写)12中间接头浸水试验22kV,30次循环(投标人填写)13附件允许短路容量25kA(投标人填写)14附件正常运行时最高允许温度90℃(投标人填写)15附件短路时最高允许温度250℃(投标人填写)表2电缆附件运行参数表序号项目单位标准参数值投标人保证值1适应的环境温度范围℃-25~+45(投标人填写)2使用地区海拔m≤2500(投标人填写)3户外终端外绝缘爬电距离mm380(投标人填写)4附件设计使用年限年30(投标人填写)表3电缆户外终端结构参数表序号项目单位标准参数值投标人保证值1基本结构(冷缩式、预制式和热缩式)冷缩式(卖方型号)2出线金具材质国标T2电解铜,镀锡(投标人填写)规格mm2(见表7)(投标人填写)质量kg满足国标GB14315(投标人填写)与电缆导体连接方式机械压接(投标人填写)3绝缘件冷缩式、预制式材料进口液态硅橡胶(投标人填写)材料牌号和生产厂投标人提供(投标人填写)质量kg投标人提供(投标人填写)外绝缘爬电距离mm380(投标人填写)热缩式材料——(投标人填写)质量kg——(投标人填写)绝缘管长度×收缩前厚度mm×mm——(投标人填写)应控管尺寸×收缩前厚度mm×mm——(投标人填写)4户外终端相色带(投标人填写)(投标人填写)5接地方式铜屏蔽层与铠装层分别接地(屏蔽接地线要求带绝缘外皮)(投标人填写)6接地铜编织线截面积mm225mm2(投标人填写)(投标人填写)7户外终端顶部的防水方式(投标人填写)(投标人填写)8其他配套材料(包括易耗品)明细表(投标人填写如下)序号名称数量单位生产厂家用途12345678910表4电缆户内终端结构参数表序号项目单位标准参数值投标人保证值1基本结构(冷缩式、预制式和热缩式)冷缩式(卖方型号)2出线金具材质国标T2电解铜,镀锡(投标人填写)规格mm2(见表7)(投标人填写)质量kg满足国标GB14315(投标人填写)与电缆导体连接方式机械压接(投标人填写)3绝缘件冷缩式、预制式材料进口液态硅橡胶(投标人填写)?材料牌号和生产厂(投标人填写)(投标人填写)质量kg(投标人填写)(投标人填写)外绝缘爬电距离mm250(投标人填写)热缩式材料——(投标人填写)质量kg——(投标人填写)绝缘管长度×收缩前厚度mm×mm——(投标人填写)应控管尺寸×收缩前厚度mm×mm——(投标人填写)4接地方式铜屏蔽层与铠装层分别接地(屏蔽接地线要求带绝缘外皮)(投标人填写)4接地铜编织线截面积mm225mm2(投标人填写)(投标人填写)5其他配套材料(包括易耗品)明细表(投标人填写如下)序号名称数量单位生产厂家用途12345678910表5电缆插拔式终端结构参数表序号项目单位标准参数值投标人保证值1基本结构/预制式2出线金具材质/紫铜镀锡规格mm2质量kg/前后接头整体长度mm/与电缆导体连接方式/压接3绝缘件冷缩式、预制式材料//材料牌号和生产厂//4结构高度mm/5终端相色带红绿黄6接地方式铜屏蔽层与铠装层分别接地(屏蔽接地线要求带绝缘外皮)7接地铜编织线截面积mm225mm28其他配套材料(包括易耗品)明细表(投标人填写如下)序号名称数量单位生产厂家用途表6电缆接头结构参数表序号项目单位标准参数值投标人保证值1基本结构(冷缩式、预制式和热缩式)冷缩式(卖方型号)2连接金具材质国标T2电解铜,镀锡(投标人填写)规格mm2(见表6)(投标人填写)质量kg满足国标GB14315(投标人填写)与电缆导体连接方式机械压接(投标人填写)3绝缘件冷缩式、预制式材料进口液态硅橡胶(投标人填写)材料牌号和生产厂(投标人填写)(投标人填写)质量kg(投标人填写)(投标人填写)最大外径×长度mm×mm(投标人填写)(投标人填写)热缩式材料——(投标人填写)绝缘管层数层不超过两层(投标人填写)绝缘管长度×收缩前厚度mm×mm——(投标人填写)应控管尺寸×收缩前厚度mm×mm——(投标人填写)4冷缩部件的扩张率3倍(投标人填写)5是否进行扩张状态下100%出厂老化测试(60℃,72小时)(投标人填写)6中间接头的外屏蔽层的厚度mm1.5mm(投标人填写)7中间接头铜屏蔽网套截面积mm225mm2(投标人填写)8中间接头内界面绝缘填充剂类型(投标人填写)9出厂电气试验率100%(投标人填写)10冷缩附件扩张状态的储存时间2年(投标人填写)11结构尺寸(外径×长度)mm×mm(投标人填写)12提供中间接头本体防水试验报告VDE水中恒压负荷试验和第三方权威检测机构水中运行证明报告(投标人填写)5其他配套材料(包括易耗品)明细表(投标人填写如下)序号名称单位数量生产厂家用途123456表5(续)序号名称数量单位生产厂家用途78910注热缩式电缆接头如果由两层绝缘管组成,应分别填每层的绝缘管长度×收缩前厚度。2项目需求部分2.1货物需求及供货范围一览表表7货物需求及供货范围一览表(铜芯)序号材料名称单位项目单位要求投标人响应备注型号规格数量型号规格数量110kV电缆户外终端套冷缩式35mm2冷缩式50mm2冷缩式70mm2冷缩式95mm2冷缩120mm2冷缩150mm2冷缩185mm2冷缩240mm2冷缩300mm2冷缩400mm2210kV电缆户内终端套冷缩式35mm2冷缩式50mm2冷缩式70mm2冷缩式95mm2冷缩120mm2冷缩150mm2冷缩185mm2冷缩240mm2冷缩300mm2冷缩400mm2310kV电缆插拔终端套冷缩式35mm2冷缩式50mm2冷缩式70mm2冷缩式95mm2冷缩120mm2冷缩150mm2冷缩185mm2冷缩240mm2冷缩300mm2冷缩400mm2410kV电缆中间接头套冷缩式35mm2冷缩式50mm2冷缩式70mm2冷缩式95mm2冷缩120mm2冷缩150mm2冷缩185mm2冷缩240mm2冷缩300mm2冷缩400mm22.2必备的备品备件、专用工具和仪器仪表供货表表8必备的备品备件、专用工具和仪器仪表供货表序号名称单位项目单位要求投标人响应备注型号和规格数量型号和规格数量123452.3投标人应提供的有关资料2.3.1电缆终端和接头内部场强的选取依据。2.3.2电缆附件电场分析曲线。2.3.3电缆附件的结构图纸。2.3.4绝缘料、硅脂、清洗剂等主要性能。2.
本文标题:18、10kV电缆附件专用技术规范
链接地址:https://www.777doc.com/doc-7928358 .html