新格林耐特配置命令

新格林耐特第1页共8页第一部分：TiNetS2000EI系列配置命令及说明（红色标识为一些常用命令）Username(1-32chars):adminPassword(1-16chars):******/登陆交换机，默认密码123456/TiNetenable/进入特权模式/TiNet#configureterminal/进入全局模式/TiNet(config)#1.TINET#terminallanguage/改变语言模式/例如：TINET#terminallanguageChinese/改成中文模式/2.TiNet#clearstartup-config/清除配置，恢复出厂默设置/3.TiNet#copyrunning-configstartup-config/保存配置命令/4.TiNet#load?application下载应用程序configuration下载配置文件keyfile下载SSH密钥文件whole-bootrom下载全部的bootrom/设备升级命令/5.TiNet(config)#ipaddress192.168.1.5255.255.255.0192.168.1.1/配置交换机IP地址/6.TiNet(config)show？/show命令，后可以打问号/ShowipShowmacShowinterfaceShowvlan7.TiNet(config)#vlan3901/建立VLAN3901/TiNet(config-if-vlan)#switchportethernet0/1/把端口1加入该VLAN/TiNet(config)#ipvlan3901/定义管理vlan为3901TiNet(config)#noipvlan1/删除默认管理VLAN1/8.TiNet(config)#vlan1001-1512/批量建立VLAN/9.TiNet(config-if-vlan)#switchportethernet0/2toethernet0/8ethernet0/11ethernet0/16/在某一VLAN中或者VLAN段中批量加入端口/新格林耐特第2页共8页10.TiNet(config-if-ethernet-0/16)#tagvlan1001,1112-1512,4000/端口下批量打tag/11.TiNet(config-if-ethernet-0/1)#switchportmodetrunk/改变端口模式，为trunk模式/12.TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall/端口为trunk模式，允许所有VLAN通过/13.TiNet(config-if-ethernet-0/2)#switchportaccessvlan1001/改变端口PVID/14.TiNet(config)#port-isolationethernet?STRING3-4端口号为槽端口号0-2/端口号1-24TiNet(config)#port-isolationethernet0/2toe0/16添加端口隔离下行端口成功./一步隔离，一条命令隔离除上行口以外所有端口/15.TiNet(config)#interfacerangeethernet0/2toethernet0/16/批量端口处理命令/16.TiNet(config-if-range)#bandwidth-control?egress出口带宽控制ingress入口带宽控制/端口限速命令/17.TiNet(config)#showutilizationinterface/实时查看端口流量占比/LinkUtilizationAveragesThuJan100:43:201970portlinkReceivePeakRxTransmitPeakTxStatuspkts/secpkts/secpkts/secpkts/sec==================================================================e0/1down0000e0/2down0000e0/3down0000e0/4down0000e0/5down0000e0/6down0000e0/7down0000e0/8down0000e0/9down0000e0/10down0000e0/11down0000e0/12down0000e0/13down0000e0/14down0000e0/15down0000新格林耐特第3页共8页e0/16down0000e1/1down0000====spacebar-togglescreenU-pageupD-pagedownCR-exit====通过空格键来切换回车键结束查看18.TiNet(config)#usernamechange-passwo请输入您的登录密码:******请输入用户名(4--15位):admin请输入新口令(1--15位):********输入确认口令(1--15位):********用户admin密码修改成功。/修改登陆密码/新格林耐特第4页共8页配置案例：小河区某小区格林耐特设备配置简要流程TiNet(config)#ipaddress119.1.176.185255.255.255.0119.1.176.1/配置ip地址/ConfigIPsuccessfully.TiNet(config)#showipSwitchconfigurationipobtained:MANUALipaddress:119.1.176.185netmask:255.255.255.0gateway:119.1.176.1ManageVLAN:1MACaddress:00:0a:5a:11:ba:b8/查看交换机ip地址/TiNet(config)#exTiNet#terminallanguagechinese/更改语言模式为中文/TiNet(config)#vlan3901/建立vlan3901/TiNet(config-if-vlan)#switchportall/在vlan3901下添加端口/添加VLAN端口成功!TiNet(config)#ipaddressvlan3901/定义交换机管理vlan/配置管理VLAN成功!TiNet(config)#showip交换机的配置信息IP地址获得方式:MANUALIP地址:119.1.176.185子网掩码:255.255.255.0网关地址:119.1.176.1管理VLAN:13901/此时管理vlan为1和3901/MAC地址:00:0a:5a:11:ba:b8TiNet(config)#noipaddressvlan1/删除交换机默认管理vlan1/删除管理VLAN成功!新格林耐特第5页共8页TiNet(config)#showip交换机的配置信息IP地址获得方式:MANUALIP地址:119.1.176.185子网掩码:255.255.255.0网关地址:119.1.176.1管理VLAN:3901MAC地址:00:0a:5a:11:ba:b8/管理vlan已改为3901/TiNet(config)#interrangeethernet0/1toethernet0/16/批量进入端口1-16TiNet(config-if-range)#tagvlan3901/端口1-16tagvlan3901/TiNet(config-if-range)#exTiNet(config)#vlan1001/建立vlan1001/TiNet(config-if-vlan)#switchportethernet0/1/vlan1001中加入端口1/添加VLAN端口成功!TiNet(config-if-vlan)#showvlan1001显示VLAN信息VLANID:1001VLANstatus:staticVLANmember:e0/1.Statictaggedports:StaticuntaggedPorts:e0/1.Dynamictaggedports:TiNet(config)#vlan1015-1030/批量建立vlan1015-1030/TiNet(config-if-vlan)#switchportethernet0/1ethernet0/16/vlan1015-1030加入端口1-16/添加VLAN端口成功!TiNet(config-if-vlan)#showvlan1015显示VLAN信息VLANID:1015VLANstatus:staticVLANmember:e0/1,e0/16.Statictaggedports:StaticuntaggedPorts:e0/1,e0/16.Dynamictaggedports:TiNet(config)#port-isolationethernet0/2toe0/16/端口2-16进行隔离，1口为上行口，未隔离/添加端口隔离下行端口成功.TiNet(config-if-ethernet-0/1)#switchport?accessaccess端口新格林耐特第6页共8页backup配置备份端口mode端口模式trunktrunk端口TiNet(config-if-ethernet-0/1)#switchportmodetrunk/更改端口1模式为trunk/TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall/允许所有vlan通过1口/TiNet(config-if-ethernet-0/1)#switchporttrunknativevlan3901/更改1口pvid为3901/TiNet(config-if-ethernet-0/1)#exTiNet(config)#showutilizationinterface/查看端口实时流量/LinkUtilizationAveragesThuJan100:24:371970portlinkReceivePeakRxTransmitPeakTxStatuspkts/secpkts/secpkts/secpkts/sec==================================================================e0/1down0000e0/2down0000e0/3down0000e0/4down0000e0/5down0000e0/6down0000e0/7down0000e0/8down0000e0/9down0000e0/10down0000e0/11down0000e0/12down0000e0/13down0000e0/14down0000e0/15down0000e0/16down0000e1/1down0000====spacebar-togglescreenU-pageupD-pagedownCR-exit====TiNet(config)#usernamechange-password/修改登录密码/请输入您的登录密码:******请输入用户名(4--15位):admin请输入新口令(1--15位):******输入确认口令(1--15位):******/用户admin密码修改成功/TiNet#copyrunning-configstartup-config/保存配置命令/新格林耐特第7页共8页第二部分：交换机实现telnet管理配置步骤第一步：配置规划好的交换机ip地址例：TiNet(config)#ipaddress119.1.176.185255.255.255.0119.1.176.1/配置ip地址/ConfigIPsuccessfully.TiNet(config)#showipSwitchconfigurationipob