变频器参数设置

UnpublishedWorkCopyright©XIZIOTISElevatorCompany调试手册西子奥的斯电梯有限公司文件编号：OH-CONB763_SUR_ZHOH-CONB763No.:OH-CONB763_SUR_ZHDate:2008-12-15Page:2/631.0~2.5m/sFIM工地调试手册PackUnpublishedWorkCopyright©XIZIOTISElevatorCompany原始会签记录编制卢翊校对王恒审核李强批准刘祖斌部门PDC部门PDC部门EC部门PDC日期2008-12-15日期2009-02-05日期2009-02-08日期2009-02-08授权AUTH.CAL4733部件版本部件名称硬件版本软件版本GECBGDA26800LJ1GAA30780DAG或更高KAA26800ABG1GAA30780DAG或更高KAA26800ABG4GAA30780DAG或更高MCBCXAA26805AAA2X2230581AAA或更高变频器FRExxxLM1S-4XO11110或更高注意：部件版本可能会随时更新，有需要最新部件版本参数和I/O表，请上工程中心网站读取或下载。OH-CONB763No.:OH-CONB763_SUR_ZHDate:2008-12-15Page:3/631.0~2.5m/sFIM工地调试手册PackUnpublishedWorkCopyright©XIZIOTISElevatorCompany更改记录序号更改PC更改内容描述更改日期签名1CAL50161）更改第1页，变频器软件版本号；2）第5页，XO1产品规格书的文件编号；3）第16页，增加F4、F5说明；第23页，更改DCS说明2009-03-16卢翊2CAL54691）为提高开门效率，更改第10页，H67=0.8更改为H67=0.4；更改第12页，L83=0.3更改为L83=0.2，L86=1.2更改为L86=0.2；2）为消除停车段电梯抖动问题，更改第15页，F4=0更改为F4=17.3）为解决群控梯底层错层问题，更新MCBC软件，增加MCBC参数设置，更改第16页，将原无效参数F13:OpenDoorSpeed更改为F13:BottomLanding.4）更改第22页，更正平层光电（1LV/2LV）类型，由常开更改为常开。2009-05-27王恒3CAL57791）第16页,由于软件更新，更改MCBC的F13参数。2）第34页,增加一个MCBC的故障信息。2009-07-27薛维祥4CAL58681）第1页修改MCBC件号；2）第13页增加不同主机时的变频器参数设置说明。2009-07-29卢翊5CAL80521）第2页，修改软件版本号；2）第9、16、17页，修改GECB及MCBC出厂参数值；3）第43页，增加上行超速保护的测试方式。2010-06-22王恒6CAL8274第17页更改MCBC参数描述2010-11-16王恒7CAL8751更改第6~8,25页，增加P44~P63页，增加GECB参数、问题诊断及功能设置说明2011-03-09王恒8910111213ThisworkandtheinformationitcontainsarethepropertyofXiziOtisElevatorCompany(“XOEC”).Itisdelivered～othersontheexpressconditionthatitwillbeusedonlyfor,oronbehalfof,XOEC;thatneitheritnortheinformationitcontainswillbereportedordisclosed,inwholeorinpart,withoutthepriorwrittenconsentofXOEC,andthatondemanditandanycopieswillbepromptlyreturned～XOEC.OH-CONB763No.:OH-CONB763_SUR_ZHDate:2008-12-15Page:4/631.0~2.5m/sFIM工地调试手册PackUnpublishedWorkCopyright©XIZIOTISElevatorCompany目录1概述.............................................................................................................................................................52检修模式运行条件检查................................................................................................................................73检修模式GECB上电检查...........................................................................................................................84变频器参数设置.........................................................................................................................................105MCBC参数确认........................................................................................................................................166主机磁极自整定.........................................................................................................................................177电梯运行方向检查.....................................................................................................................................218点动运行模式.............................................................................................................................................219位置参考系统调整.....................................................................................................................................2110首次正常运行准备......................................................................................................................................2311井道位置自学习.........................................................................................................................................2312DCS(门检测运行)操作...............................................................................................................................2513正常运行....................................................................................................................................................2614平衡系数调整.............................................................................................................................................2615正常运行的平层位置的调整.......................................................................................................................2616故障排除....................................................................................................................................................2717上行超速保护测试操作..............................................................................................................................4318GECB常见问题处理..................................................................................................................................4419GECB特殊功能设置..................................................................................................................................4520GECB参数设置.........................................................................................................................................47OH-CONB763No.:OH-CONB763_SUR_ZHDate:2008-12-15Page:5/631.0~2.5m/sFIM工地调试手册PackUnpublishedWorkCopyright©XIZIOTISElevatorCompany1概述OH-CONB763控制系统引用了GECB作为电梯控制系统的核心，充分吸收了OTIS技术，利用OTIS高可靠性的CAN-Bus通讯系统，将电梯的各个部件紧密的连在一起。驱动部分则采用日本富士高精度的矢量变频技术，使电梯的运行更加平稳舒适。1.1.总体框图下图为OH-CONB763控制系统的基本框图和信号流程