51单片机的室内空气质量检测系统设计论文定稿

I基于单片机的气体质量检测系统的设计摘要本论文研究设计了一种用于公共场所及室内具有检测及超限报警功能的室内空气质量检测系统。其设计方案基于89C51单片机，选择瑞士蒙巴波公司的CH20/S-10甲醛传感器和MQ-5气体传感器。系统将传感器输出的4~20mA的标准信号通过以AD0832为核心的A/D转换电路调理后，经由单片机进行数据处理，最后由LCD显示甲醛浓度值。文中详细介绍了数据采集子系统、数据处理过程以及数据显示子系统和报警电路的设计方法和过程。系统对于采样地点超出规定的甲醛容许浓度和天然气规定浓度时采用三极管驱动的单音频报警电路提醒监测人员。同时，操作人员对于具体报警点的上限值可以通过单片机编程进行设置。另外，该系统对浓度信号进行了信号补偿等处理，减少了测量误差，因此，具有较高的测量精度，而且结构简单，性能优良。本系统的量程为0-10ppm，精度为0.039ppm。关键词:甲醛检测/天然气检测/AT89C52单片机IIABSTRACTThisthesisdesignofapaperforpublicplacesandindoortestingandover-limitalarmfunctionswithindoorairqualitytestingsystem.Itsdesignisbasedon89C51singlechip,withthechoiceofMQ-5gassensorsandCH20/S-10formaldehydesensorfromSwitzerlandmengbabocompany.Sensorsystemwilloutput4~20mAstandardsignalthroughthecoreADC0832forA/Dconversioncircuitafterconditioning,bythesingle-chipmicrocomputerfordataprocessing,atlastdisplaytheformaldehydeconcentrationontheLCD.Thearticledetailedthedataacquisitionsubsystem,dataprocessinganddatadisplayandalarmsystemcircuitdesignmethodandprocess.WhenthesamplingsiteswhentheformaldehydeandNaturalgasconcentrationexceeded，Tothesingle-transistordrivecircuitaudioalarmwillsoundthealarm，Testingstafftoremind.Atthesametime，Theconcentrationofformaldehyde,Canbesetthroughthesingle-chipprogramming.Inaddition,thesystemsignalsaconcentrationcompensationsignalprocessing,areductionofmeasurementerror,therefore,haveahighmeasurementaccuracy,andsimplestructure,excellentperformance.Therangeofthesystemfor0-10ppm,accuracy0.039ppm.Keywords:Formaldehydedetection,Naturalgasdetection,AT89C52single-chip0目录中文摘要.............................................................................................I英文摘要............................................................................................II1绪论.................................................................................................11.1引言................................................................................................1２概述............................................................................................22.1系统总概述....................................................................................22.2总体方案设计................................................................................22.3硬件设计........................................................................................22.4软件设计........................................................................................32.5硬件结构.......................................................................................32.6软件结构.......................................................................................33硬件设计......................................................................................43.1硬件设计主电路图.....................................................................43.2硬件选择.....................................................................................43.2.1MCU的选择与简介...........................................................................43.2.2单片机最小系统的实现......................................................................63.2.3数据采集系统......................................................................................83.2.4模数转换的选择与简介....................................................................113.2.5按键选择与简介................................................................................133.2.6外围扩充存储器................................................................................133.2.7时钟芯片选择与简介........................................................................143.2.8上拉电阻............................................................................................153.2.9液晶显示器简介................................................................................153.2.10报警电路............................................................................................163.2.11硬件仿真环境介绍............................................................................164软件设计.......................................................................................1814.1编写语言的选择.........................................................................184.2编译软件介绍.............................................................................184.3主程序模块.................................................................................184.4模数转换......................................................................................194.5按键模块......................................................................................194.6时钟模块......................................................................................204.7液晶显示模块..............................................................................205系统仿真.......................................................................................21结束语..............................................................................................23致谢..............................................................................................24参考文献..........................................................................................25附