工艺合并数据汇总(整理)

物料代码物料描述工序号工作中心代码工序短文本(40字符)工序长文本20000372MH1109-00-01-0020WWX01烤黑漆20000379MH1109-00-0540WWX01镀白锌20000384MH1109-00-07-0140WWX01烤黄漆20000387MH1109-00-1040WWX01烤灰白漆20000388MH1109-00-1140WWX01烤灰白漆20000390MH1109-00-1330WWX01烤灰白漆20000391MH1109-00-1440WWX01烤蓝漆20000401MH1109-01-03-0720WWX01线切割开大料，按400x150x5开料(1件可割20件），线切割零件外形。20000422MH1109-02-0140WWX01发黑20000423MH1109-02-0220WWX01调质调质HB235～25520000423MH1109-02-0240WWX01发黑20000434MH1109-03-02-01-01A10WWX01线切割20000434MH1109-03-02-01-01A20WWX01镀硬铬镀层厚0.01至0.0320000437MH1109-03-0440WWX01发黑20000438MH1109-03-05A50WWX01发黑20000439MH1109-03-0640WWX01镀白锌20000440MH1109-03-0710WWX01按图外购20000440MH1109-03-0720WWX01镀白锌20000441MH1109-03-08A20WWX01调质调质硬度：HB220～25020000441MH1109-03-08A60WWX01喷砂B面喷砂，粒度0.4mm20000441MH1109-03-08A70WWX01镀硬铬20000442MH1109-03-0930WWX01调质调质HB235～25520000444MH1109-03-11A50WWX01线切割线切割弧形，注意保护表面20000444MH1109-03-11A60WWX01镀装饰铬保证尺寸8（0/-0.05）20000449MH1109-03-1640WWX01旋风铣齿外协铣齿20000452MH1109-03-1940WWX01镀白锌20000453MH1109-03-2040WWX01镀白锌注意两公差孔φ20和φ27内孔不镀锌20000461MH1109-04-0230WWX01线切割加工外形及φ21孔和M12螺纹底孔，保证孔距公差要求及外形尺寸20000461MH1109-04-0250WWX01烤灰白漆20000462MH1109-04-0310WWX01按图外购20000462MH1109-04-0320WWX01镀白锌20000464MH1109-04-0530WWX01镀白锌保证公差外圆尺寸20000465MH1109-04-06-0020WWX01镀白锌20000468MH1109-04-07A30WWX01镀白锌保证公差外圆尺寸20000469MH1109-04-0820WWX01镀白锌#N/AMH1109-05-01-0020WWX01镀白锌#N/AMH1109-05-01-0110WWX01锯切开料：热轧圆钢_φ28/A3L=307MM#N/AMH1109-05-01-0230WWX01外协线切割加工外形，φ12MM公差孔及1MM和2MM槽20000472MH1109-05-0240WWX01镀硬铬20000473MH1109-05-0360WWX01烤黑漆20000474MH1109-05-04A30WWX01线切割注意线切割方孔与螺孔的相对位置合图（只需线割内框）20000475MH1109-05-0520WWX01调质调质235～25520000476MH1109-05-0660WWX01镀硬铬镀层厚0.03～0.0520000485MH1109-05-0950WWX01镀白锌保证公差外圆尺寸20000486MH1109-05-10A30WWX01表面高频淬火￠68外圆表面淬火ＨＲＣ59～6120000486MH1109-05-10A60WWX01镀硬铬注：表面镀硬铬，孔不镀铬20000488MH1109-06-0140WWX01镀白锌20000489MH1109-06-02-0030WWX01烤黑漆20000492MH1109-06-0310WWX01按图外购20000492MH1109-06-0320WWX01镀白锌20000497MH1109-06-0540WWX01镀白锌20000498MH1109-06-06A30WWX01镀白锌20000499MH1109-06-0740WWX01镀白锌20000500MH1109-06-0830WWX01镀白锌20000502MH1109-06-10A30WWX01镀白锌20000503MH1109-06-1140WWX01镀白锌保证公差外圆尺寸20000504MH1109-06-1230WWX01镀白锌保证公差外圆尺寸。20000505MH1109-06-1320WWX01镀白锌20000531MH1109-07-0330WWX01镀白锌20000532MH1109-07-04-0020WWX01烤黑漆20000535MH1109-07-0540WWX01烤黑漆20000536MH1109-07-0640WWX01烤黑漆20000547MH1109-09-01-0020WWX01烤灰白漆20001400MH2324-02-02-00A_上压板30WWX01退火处理20001447MH2324-05-11_上横梁挡板30WWX01烤蓝漆。20001448MH2324-05-12_下横梁挡板30WWX01烤蓝漆。#N/AMH2324-05-13_气缸法兰30WWX01镀白锌20001363MH2324-00-03-00A_侧挡板30WWX01退火处理。20001367MH2324-00-04-00A_下挡板20WWX01退火处理。20001371MH2324-00-05_侧门50WWX01烤蓝漆。20001416MH2324-04-01_导向条30WWX01镀白锌20001419MH2324-04-03-00_侧压板20WWX01退火处理。20001451MH2324-06-01-00_油箱20WWX01烤漆（墨绿色）。20001455MH2324-06-02_油箱盖板60WWX01烤漆（墨绿色）。#N/AMH3848A×100(3)-00-17-0020WWX01烤蓝绿漆20002040MH3848A×100(3)-07-0830WWX01烤蓝漆20002064MH3848A×100(3)-09-03-0140WWX01烤黄漆20001989MH3848A×100(3)-04-0840WWX01烤绿漆20002046MH3848A×100(3)-07-1130WWX01烤蓝绿漆。20002048MH3848A×100(3)-07-14-00A20WWX01烤蓝绿漆，注意：外螺纹和内锥面及内孔要包住，不能烤漆。20002051MH3848A×100(3)-07-15-00A20WWX01烤蓝绿漆，注意：外螺纹和内锥面及内孔要包住，不能烤漆。20002053MH3848A×100(3)-07-17A-0050WWX01烤蓝绿漆，注意：外螺纹和内锥面及内孔要包住，不能烤漆。20002055MH3848A×100(3)-08-0140WWX01表面镀白锌。20002057MH3848A×100(3)-09-01-0020WWX01表面烤波纹漆（蓝緑色）。20001901MH3848A×100(3)-00-0140WWX01烤绿漆。20001902MH3848A×100(3)-00-0240WWX01烤绿漆。20001903MH3848A×100(3)-00-0340WWX01烤绿漆。20001906MH3848A×100(3)-00-06A-0040WWX01烤蓝漆。20001911MH3848A×100(3)-00-0930WWX01烤蓝漆。20001912MH3848A×100(3)-00-1040WWX01烤蓝漆。#N/AMH3848A×100(3)-00-12A-0050WWX01烤蓝绿漆。#N/AMH3848A×100(3)-00-13A-0050WWX01烤蓝绿漆。#N/AMH3848A×100(3)-00-15A-0020WWX01烤蓝绿漆。20001922MH3848A×100(3)-00-1630WWX01烤蓝绿漆。20001973MH3848A×100(3)-03-0630WWX01镀白锌。20001974MH3848A×100(3)-03-0730WWX01镀白锌。#N/AMH3848A×100(3)-03-08-0020WWX01烤蓝绿漆。#N/AMH3848A×100(3)-03-10-0020WWX01烤蓝绿漆。20001996MH3848A×100(3)-05-0330WWX01烤黄漆。20001997MH3848A×100(3)-05-0430WWX01烤黄漆。20001999MH3848A×100(3)-05-0730WWX01烤黄漆。20002000MH3848A×100(3)-05-0830WWX01烤黄漆。20002003MH3848A×100(3)-06-0110WWX01激光割周边以及全部通孔和螺纹底孔。20002003MH3848A×100(3)-06-0130WWX01烤墨绿色。20002004MH3848A×100(3)-06-02-0020WWX01烤蓝绿漆。20002014MH3848A×100(3)-07-01-00A30WWX01烤蓝绿漆。20002024MH3848A×100(3)-07-02-0030WWX01烤蓝绿漆。20002030MH3848A×100(3)-07-03A-0050WWX01烤蓝绿漆。20002033MH3848A×100(3)-07-04A-0050WWX01烤蓝绿漆。20002035MH3848A×100(3)-07-05A-0050WWX01烤蓝绿漆。20002037MH3848A×100(3)-07-06A-0050WWX01烤蓝绿漆。20002039MH3848A×100(3)-07-07A-0050WWX01烤蓝绿漆。20002041MH3848A×100(3)-07-0950WWX01烤蓝绿漆。20002042MH3848A×100(3)-07-10-0030WWX01烤蓝绿漆。20001994MH3848A×100(3)-05-0230WWX01烤黄漆。20000054MF5036C-02-01-00A20WWX01烤蓝绿漆。20000057MF5036C-02-02A50WWX01烤蓝绿漆。20002444MH6113A-00-01-0020WWX01外协烤蓝漆，烤漆前表面要处理干净20002447MH6113A-00-0260WWX01外协烤橘红漆20002448MH6113A-00-03A60WWX01外协烤橘红漆20002453MH6113A-00-0830WWX01外协烤蓝漆20002454MH6113A-00-0930WWX01外协烤蓝漆20002456MH6113A-00-1150WWX01外协烤蓝漆20002458MH6113A-00-1350WWX01外协烤灰白漆,烤漆前表面要清理干净20002459MH6113A-00-1420WWX01外协烤蓝漆20002477MH6113A-00-1840WWX01烤蓝漆，烤漆前表面要出来干净20002478MH6113A-00-19A30WWX01镀锌前表面要处理干净#N/AMH6113A-00-20-0020WWX01烤蓝漆前表面要处理干净20002481MH6113A-00-2150WWX01烤蓝漆前表面要处理干净2000