kisssoft中文教程-徐徐

本人刚刚接触kisssoft，鉴于目前中文资料少，特翻译了一点实例。希望更多的高手们能写更多上乘的实例，推动新手更加快速的发展和成长。1、soft是单个零部件sys是系统system的缩写（多个零件组成的部件）2、启动kisssys3、打开一个文件帮助文档的路径File—open---打开C:\ProgramFiles\KISSsoft03-2011\kisssys\tutorial\KISSsys-Tutorial-001.ks4、调出视图窗口显示和隐藏模型树、模板、信息kisssoft窗口等去掉前面的钩子（对号），就可以隐藏相对应的部分。添加对号，可以显示相应的部分。5、示意图----反映了载荷传递的路径。左击移动任何一个方框，箭头跟着一起改变。6、模型树含义：（查看每一个轴和轴上；零部件的装配）红色的S1表示第一个轴上的零件，第二个s1表示第1根轴.s是shaft轴的简写。双击轴s1，弹出轴和轴上零部件的布置。Z1、Z2、Z3、Z4、分别表示齿轮1234.B1、b2分别表示轴承12.标号顺序沿着载荷传递的路径。可以编辑轴和轴上零部件的位置。。。拖动轴承支架的位置。。直接关掉右上角窗口，返回到3D模型窗口编辑轴后，更新减速器gearbox。6、运动学动力学计算Calculatekinematics未完，待续。。。indexableturningtoolfinite-elementanalysisStaticanalysisresultsofindexableturningtool可转位车刀有限元模型的建立EstablishmentofFEMmodelindexableturningtoolModelandthesolvingofshapeoptimizationbladeofindexableturningtooliterationcurveobjectivefunctionandshapevariableonrod3.5Summary...................................................................................................错误!未定义书签。CHAPTER4硬质合金可转位车刀的形状优化设计.............................................错误!未定义书签。4.1introduction...............................................................................................错误!未定义书签。4.2DesignExampleofindexableturningtool..........................................错误!未定义书签。4.3finite-elementanalysisofindexableturningtoo可转位车刀的有限元分析.错误!未定义书签。4.3.1可转位车刀有限元模型的建立..............................................................错误!未定义书签。4.3.2可转位车刀静力分析结果......................................................................错误!未定义书签。4.3.3可转位车刀有限元结果分析..................................................................错误!未定义书签。4.4shapeoptimizationindexableturningtool...........................................错误!未定义书签。4.4.1shapevariableofrod.................................................................................错误!未定义书签。4.4.2iterationcurveobjectivefunctionandshapevariableonrod..........错误!未定义书签。4.5shapeoptimizationbladeofindexableturningtool............................错误!未定义书签。4.5.1Optimizationmodelofblade.....................................................................错误!未定义书签。4.5.2Theextractionoftheoptimizationresults................................................错误!未定义书签。4.7Summary..........................................................................................................错误!未定义书签。CHAPTER5..............................................................topologicaloptimizationofhardalloyLathetool错误!未定义书签。5.1introduction....................................................................................错误!未定义书签。5.22DstructuretopologyofindexableturningtoolbasedonMatlab..................错误!未定义书签。5.2.1MatlabprogrammingbasedonSIMPOFOCcriterionmethord.......错误!未定义书签。5.3.22DstructuretopologyofindexableturningtoolbasedonMatlab...........错误!未定义书签。5.32Dstructuretopologyofindexableturningtoolbasedonoptistruct.............错误!未定义书签。5.43Dstructuretopologyofindexableturningtool..................................错误!未定义书签。5.4.1optimumproposal.......................................................................错误!未定义书签。5.4.2Thereconstructionofthetopologicaloptimizationresultsandcorrect..错误!未定义书签。5.4.3Validationtopologyoptimizationresults.............................................错误!未定义书签。5.5Optistruct中制造约束功能简介....................................................................错误!未定义书签。5.6Summary..........................................................................................................错误!未定义书签。CHAPTER6刀具结构优化设计平台................................................................错误!未定义书签。6.1overview..................................................................................................错误!未定义书签。6.1.1Theobjectiveoftheprototypesystemandcharacteristics.......................错误!未定义书签。6.1.2TheprincipleoftheprototypesystemandGeneralIdea............................错误!未定义书签。6.1.3environmentandtoolsofsystemdevelopment........................................错误!未定义书签。6.2Thekeytechnicalrouteandimplementation.............................................错误!未定义书签。6.3systeminterfaceandApplicationExample.......................................................错误!未定义书签。6.3.1maininterface...........................................................................................错误!未定义书签。6.3.2applicationexampleoftheprototypesystem............................................错误!未定义书签。6.4Summary...................................................................................................错误!未定义书签。ConclusionandPerspective...........................................................................错误!未定义书签。References.......................................................................................................错误!未定义书签。Acknologyments.............................................................................................错误!未定义书签。N.mm